102 Minimum Theremin Product Contents

(Back)


Product Number

Description

102-KIT  -

Complete Kit with all the parts to construct a 102 Minimum Theremin

102-PCB  -

Unpopulated Printed Circuit Board (PCB) without any components

102-PCBKIT1  -

Unpopulated Printed Circuit Board (PCB) with user-soldered, on-board components (no off-board components)

102-PCBKIT2  -

Unpopulated Printed Circuit Board (PCB) with user-soldered on-board and off-board components

102-ANT  -

Antenna Assembly including plate, threaded mast, plug and jack

102-ENC  -

Enclosure Assembly including case, front panel, antenna mounting bracket,
battery mounting bracket and all hardware

102-APCB1  -

Factory-Assembled Printed Circuit Board (PCB) with on-board components (no off-board components)

102-APCB2  -

Factory-Assembled Printed Circuit Board (PCB) with on-board components and off-board components

102-ASSEM  -

Factory-Assembled 102 Minimum Theremin

Item Quantity Included With Product Number

Item

102-KIT 102-PCB 102-PCBKIT1 102-PCBKIT2 102-ANT 102-ENC 102-APCB1 102-APCB2 102-ASSEM
1 1 1 1 0 0 1* 1* 1* Unpopulated Printed Circuit Board (PCB)
1 0 1 1 0 0 1* 1* 1* Set of Circuit Board Components (see table below)
1 0 0 1 0 0 0 1* 1* Power Switch
1 0 0 1 0 0 0 1* 1* Pitch Control Potentiometer and knob
1 0 0 1 0 0 0 1* 1* Volume Control Potentiometer and knob
1 0 0 1 0 0 0 1* 1* Output Jack
1 0 0 1 0 0 0 1 1* Ground Jack
1 0 0 1 0 0 0 1 1* Loudspeaker
1 0 0 1 1 0 0 1** 1* Antenna Jack
1 0 0 0 0 1 0 0 1* Antenna Jack Bracket
1 0 0 0 1 0 0 0 1* Antenna Assembly (see table below)
1 0 0 0 0 1 0 0 1* Case
1 0 0 0 0 1 0 0 1* Front Panel
4 0 4 4 0 4 0 0 4* #4-40 x 1.5" Hexagonal Standoff
008800000#4-40 x 0.312" Pan-Head Screw
1 0 0 0 0 1 0 0 1* Set of Hardware (see table below)
1 0 0 1 0 0 0 1* 1* Battery Connector
1 0 0 0 0 1 0 0 1* Battery Holder (clip attached to adaptor plate)
1 0 0 1 0 0 0 1 1* 9V Battery
1 0 0 1 0 0 0 0 1* Hookup Wire

 * Items in column are supplied assembled together.
** The Antenna Jack requires insertion through the outside of the enclosure.
Therefore, Product 102APCB2 is provided with wire pre-attached to the
Antenna Jack, requiring user-soldering to the Printed Circuit Board.

Set of Circuit Board Components

Note:  This list refers to Printed Circuit Boards marked "REV 1" (revision 1).

Quantity

Description

2

Capacitor, 100pF

1

Capacitor, 3300pF

4

Capacitor, 0.047uF

8

Capacitor, 10uF

1

Rectifier, 1N4004GP

1

Resistor, 2200 Ohm, 5% Accuracy

1

Resistor, 6800 Ohm, 5% Accuracy

1

Resistor, 10K Ohm, 5% Accuracy

1

Resistor, 22K Ohm, 5% Accuracy

3

Resistor, 27K Ohm, 5% Accuracy

1

Resistor, 15K Ohm, 1% Accuracy

1

Resistor, 12.7K Ohm, 1% Accuracy
2 Resistor, 150K Ohm, 1% Accuracy
1Resistor, Selected Value, 1% Accuracy

1

Trimmer Potentiometer, 5K Ohm
1Trimmer Potentiometer, 100K Ohm

2

Integrated Circuit, CD4001BE

1

Integrated Circuit, NJM2113D

1

Voltage Regulator, LP2950ACZ-5.0

Antenna Assembly

Quantity

Description

1

Antenna Plate, 6" x 6"

1

Threaded Mast Rod, #6-32 x 6"

1

Banana Plug
2#6 Flat Washer

1

#6 Split-Ring Lockwasher

1

#6 Inside-Tooth Lockwasher

3

#6-32 Hex Nut

Set of Hardware

Quantity

Description

10

#4-40 x 0.312" Pan-Head Screw

4

#6-32 x 0.375" Pan-Head Screw

4

#4-40 x 0.375" Flat-Head Screw

4

#6 Lockwasher

4

#6-32 Hex Nut



(top)

Text, images, and format 2013, 2016, 2017 by Harrison Instruments, Incorporated. No part of this page may be reproduced without express written consent of the copyright holder.
The 102 Minimum Theremin design is used by licensed agreement with its owner. Specifications may change without notice.

The purchase of these products from Harrison Instruments or a third party does not convey a license to the buyer.

20170520